Things should be avoided while monetizing your blog

Making money from your blog might sound like a great idea, but there are things you should not do if you want to ensure your blog retains its audience, continues to attract new visitors, and stays in the good graces of search engines such as Google. Making money is not a bad intention while blogging using premium hosting plan, but breaking a law while earning can damage your blogging experience. So, don't take your blogging as a business, do it to share details, content that are useful for visitors and can be read for longer period of time.

Furthermore, you need to be aware of online advertising laws that affect bloggers and follow them. Here are some things you should avoid when it comes to blog monetization:

Getting too intrusive: Your blog monetization efforts should not interrupt the user experience on your blog. Placing popup ads on your blog which are opened up whenever visitor visit your website or placing too many ads on single page can also affect traffic to your blog.

Detracting from the user experience: Ads and monetization tactics should enhance the user experience on your blog and add value to it, not damage it. The visitors like more those sites which give them better solution to their queries searching on Internet. Focus on audience and understand their point of view, place 2-3 ads on a single page but, ads should not be adult or open in popup window.

Being mistaken for spam: Search engines like Google identify websites that publish more ads than original content as spam. Even if only one page of your blog contains more ads than original content, visitors, Google, or other search engines could flag your entire blog as spam. If that happens, your blog might be removed from search engine results entirely, and the traffic that comes to your blogs from search engine will plummet.

Breaking the law: Even bloggers must follow the law, and the onus is on the publisher, or the blogger, to know what laws apply to them.

Comments

Buzzer interface with 8051 microcontroller

Buzzer is a electronic device that converts the electronic signal into buzzing noise, that is applied to it. It can be used as electronic bell or as quiz buzzer in many applications around us. Here, i world like to discuss the interfacing of a small buzzer with 8051 microcontroller and how different projects can be constructed. Buzzer Interfacing: This project shows the interface with AT89S52 microcontroller to a buzzer. When a push button is pressed, the buzzer will get ON and OFF ( number of times set in the code ) and then stops. Circuit Diagram: - The port P1 of the microcontroller is connected to buzzer. This type of connection is possible, if the current requirements of the buzzer is not more than 20mA. The output is in current source mode so that buzzer will turn ON when the output of the port is logic LOW. Switch is connected to port P3 which remains at logic HIGH by pull up resistor. Code: #include "REG52.h" #define buz P1 sbit SW=P3^0; long i...

Comparison Chart Between 8051, 8052, 8031and 8751

8051 is a popular 8-bit microcontroller and has been used in many applications since Intel introduced it. Many 8051 architecture are produced by Triscend, Intel, Atmel, Philips, Infineon (Siemens), ISSI, and Max Corp. Today, 8051 microcontrollers may not be popular but, the 8051 architecture is still popular and employed in thousands of embedded applications. This 8-bit architecture has been different segments such as 8052, 8051, 8751 and 8031 . 8052 is the super-set of 8051 and 8031 is the memory-less microcontroller hence, it has interfaced with external ROM. Whereas, 8751 chip has only 4Kbytes of on chip UV-EPROM. Everyone knows about the general 40-pin microcontroller i.e. 8051 introduced by Intel in 1980s and consists of serial communication pins, Timer, Interrupts, RAM, ROM. It has 4 ports and each port has 8 pins, total 32 pins and other 8 pins for other purposes. 8052 is the super-set of 8051 that consists of 8K bytes of internal RAM (4K in 8051), 256 by...

Different ways to generate delays in 8051

The delay length in 8051 microcontroller depends on three factors: The crystal frequency the number of clock per machine the C compiler. The original 8051 used 1/12 of the crystal oscillator frequency as one machine cycle. In other words, each machine cycle is equal to 12 clocks period of the crystal frequency connected to X1-X2 pins of 8051. To speed up the 8051, many recent versions of the 8051 have reduced the number of clocks per machine cycle from 12 to four, or even one. The frequency for the timer is always 1/12th the frequency of the crystal attached to the 8051, regardless of the 8051 version. In other words, AT89C51, DS5000, and DS89C4x0 the duration of the time to execute an instruction varies, but they all use 1/12th of the crystal's oscillator frequency for the clock source. 8051 has two different ways to generate time delay using C programming, regardless of 8051 version. The first method is simply using Loop program function in which Delay() funct...

Blogging & Tech tipps

Search This Blog