Skip to main content

Prefer Red LED over White LED in Embedded projects

The small LED (Light Emitting Diode) bulbs play a vital role in the embedded projects whether in terms of measuring the proper working of the circuit or making 8x8 LED matrix hardware for the project. Usually, students don't consider which LED should be used while making their hardware, if it is based on the collection of different LEDs. They just pick up LEDs which is available to them.

But, i would prefer them to use Red LED bulb in their project to make it look better and efficient. Now, it would be better, if you use Red LED? The fact is based on the scattering technique of visible light. The scattering of visible light is inversely proportional to the fourth power of wavelength. So, now you can get why Red LED is preferred. According the scattering of visible light (VIBGYOR), R-RED light has the highest wavelength value and from equation, it scatters less than any light in VIBGYOR. Less scattering means light will come into your eyes without much scattering and thus, allowing you to see the light even at low voltage which may not be possible in other colored LED or White LED.

What is the advantage of using Red LED?

- By reading the above, you now can get the advantages of using Red LED in your embedded project. It will appear light up even at low voltage. Hence, total voltage consumption will be less when more number of combinations of Red LEDs are used than white LEDs combination. And finally, makes your project efficient.

- Due to less scattering, it will display more clear visual, if someone makes project to display character on LED Matrix (combination of LEDs in row and column format). Thus, it gives better project presentation and clear vision to anyone who looks to your project.

- It is the reason why 7 segment displays use Red LEDs instead of using any other colored LEDs. And you will discover most of the embedded projects using this Red LED advantages to present their project.

It's totally depends on the need of one's embedded project and availability of hardware. I am not telling that you have to use only Red LED but, discussing the advantages of using Red LED and helping you in making better project.

Comments

Popular posts from this blog

Buzzer interface with 8051 microcontroller

Buzzer  is a electronic device that converts the electronic signal into buzzing noise, that is applied to it. It can be used as electronic bell or as quiz buzzer in many applications around us. Here, i world like to discuss the interfacing of a small buzzer with 8051 microcontroller and how different projects can be constructed. Buzzer Interfacing: This project shows the interface with AT89S52 microcontroller to a buzzer. When a push button is pressed, the buzzer will get ON and OFF ( number of times set in the code ) and then stops. Circuit Diagram: - The port P1 of the microcontroller is connected to buzzer. This type of connection is possible, if the current requirements of the buzzer is not more than 20mA. The output is in current source mode so that buzzer will turn ON when the output of the port is logic LOW. Switch is connected to port P3 which remains at logic HIGH by pull up resistor.  Code: #include "REG52.h" #define buz P1 sbit SW=P3^0; long i...

Comparison Chart Between 8051, 8052, 8031and 8751

8051 is a popular 8-bit microcontroller and has been used in many applications since Intel introduced it. Many 8051 architecture are produced by Triscend, Intel, Atmel, Philips, Infineon (Siemens), ISSI, and Max Corp. Today, 8051 microcontrollers may not be popular but, the 8051 architecture is still popular and employed in thousands of embedded applications. This 8-bit architecture has been different segments such as 8052, 8051, 8751 and 8031 . 8052 is the super-set of 8051 and 8031 is the memory-less microcontroller hence, it has interfaced with external ROM. Whereas, 8751 chip has only 4Kbytes of on chip UV-EPROM. Everyone knows about the general 40-pin microcontroller i.e. 8051 introduced by Intel in 1980s and consists of serial communication pins, Timer, Interrupts, RAM, ROM. It has 4 ports and each port has 8 pins, total 32 pins and other 8 pins for other purposes. 8052 is the super-set of 8051 that consists of 8K bytes of internal RAM (4K in 8051), 256 by...

Different ways to generate delays in 8051

The delay length in 8051 microcontroller depends on three factors: The crystal frequency the number of clock per machine the C compiler. The original 8051 used 1/12 of the crystal oscillator frequency as one machine cycle. In other words, each machine cycle is equal to 12 clocks period of the crystal frequency connected to X1-X2 pins of 8051. To speed up the 8051, many recent versions of the 8051 have reduced the number of clocks per machine cycle from 12 to four, or even one. The frequency for the timer is always 1/12th the frequency of the crystal attached to the 8051, regardless of the 8051 version. In other words, AT89C51, DS5000, and DS89C4x0 the duration of the time to execute an instruction varies, but they all use 1/12th of the crystal's oscillator frequency for the clock source. 8051 has two different ways to generate time delay using C programming, regardless of 8051 version. The first method is simply using Loop   program function in which Delay() funct...