How to Disable Stolen Phones

When your phone gets stolen, you immediately block your SIM card by contacting to your service provider. But this is not much to protect your stolen mobile. Thief can use your mobile by using new SIM card. But, you can also disable or make your stolen useless for him by following some steps carefully...

Disable your stolen phone by noting down 15 digit IMEI (The International Mobile Equipment Identity is a number, usually unique, to identify 3GPP (i.e., GSM, UMTS and LTE) and iDEN mobile phones, as well as some satellite phones. It is usually found printed inside the battery compartment of the phone.) number previously.

1. Press *#06# then a 15 digit code will appear on the screen. This number is unique to every handset.

2. Note it down and keep it somewhere safe. When your cell phone gets stolen then you can call your service provider and give them unique code and they will be able to block your handset. So even if the thief replace the SIM card your phone will be totally useless. You probably won't get your phone back, but at least you know that whoever stole it can't use or sell it to others. If we all follow this then there would be no point in people stealing mobile-phones.

It is simple and easy step that many people don't follow. You should make sure that your phone does not go in wrong hands and no one should make use of it for wrong purposes. So follow the above mentioned steps to disable your phone.

Comments

Comparison Chart Between 8051, 8052, 8031and 8751

8051 is a popular 8-bit microcontroller and has been used in many applications since Intel introduced it. Many 8051 architecture are produced by Triscend, Intel, Atmel, Philips, Infineon (Siemens), ISSI, and Max Corp. Today, 8051 microcontrollers may not be popular but, the 8051 architecture is still popular and employed in thousands of embedded applications. This 8-bit architecture has been different segments such as 8052, 8051, 8751 and 8031 . 8052 is the super-set of 8051 and 8031 is the memory-less microcontroller hence, it has interfaced with external ROM. Whereas, 8751 chip has only 4Kbytes of on chip UV-EPROM. Everyone knows about the general 40-pin microcontroller i.e. 8051 introduced by Intel in 1980s and consists of serial communication pins, Timer, Interrupts, RAM, ROM. It has 4 ports and each port has 8 pins, total 32 pins and other 8 pins for other purposes. 8052 is the super-set of 8051 that consists of 8K bytes of internal RAM (4K in 8051), 256 by...

Buzzer interface with 8051 microcontroller

Buzzer is a electronic device that converts the electronic signal into buzzing noise, that is applied to it. It can be used as electronic bell or as quiz buzzer in many applications around us. Here, i world like to discuss the interfacing of a small buzzer with 8051 microcontroller and how different projects can be constructed. Buzzer Interfacing: This project shows the interface with AT89S52 microcontroller to a buzzer. When a push button is pressed, the buzzer will get ON and OFF ( number of times set in the code ) and then stops. Circuit Diagram: - The port P1 of the microcontroller is connected to buzzer. This type of connection is possible, if the current requirements of the buzzer is not more than 20mA. The output is in current source mode so that buzzer will turn ON when the output of the port is logic LOW. Switch is connected to port P3 which remains at logic HIGH by pull up resistor. Code: #include "REG52.h" #define buz P1 sbit SW=P3^0; long i...

How to Switch OFF Citizen Calculator

You might be confused on seeing no OFF button on your calculator. Actually, these are general calculator available at low cost in the market. They process simple calculations like division, subtraction, Addition, Multiplication. But, how will you OFF that calculator having no option on them. There is always a trick which OFF them. It depends on the company calculator and their series to which they belong. I can tell you about Citizen Calculator CT-500 (as you can see in the image), how can you switch OFF it and can save battery too. If you leave calculator idle for 6-7 minutes, it will goes OFF automatically. My calculator goes OFF in 6.50 minutes from the point of leaving it idle. But, this is not the power saving trick for these types of calculator having not much backup battery. To save the power of your normal calculator, here is the trick to switch OFF it. Press ' /(divide sign)', 'x(multiply sign)', '%(percentage sign)', 'autoreplay option(...

Blogging & Tech tipps

Search This Blog