How to Complaint Against errant Auto-Rickshaw Drivers in Delhi

It is very common with metropolitan of India that an auto-driver refuses to take you to your destination or does not follow meter installed or over charge from customer. Now, Delhi Traffic police is advertising the complaint policy and also started message service in which you can complaint about auto-driver by just noting his auto-rickshaw number and SMS to 56767. There is not only this step that you can follow but you can also use help of popular social networking sites like Facebook and twitter.

Steps to complaint against Auto-driver:

1. SMS to 56767- if auto rickshaw refuses service, harasses in any way, does not go where you want to go, you can complaint by using Delhi traffic police SMS service. Send SMS vehicle Registration Location Time on 56767.

Eg. Send SMS to 56767.

REF- Refusal - If auto-driver does not allow you to take any where, you can use this code to send SMS.

OVC- Over Charging- if an auto-driver charges without measuring meter and over charge from you, you can use this OVC code to send SMS.

MIS- Misbehavior- If an auto-driver misbehave with you during your journey, immediately send MIS code SMS to 56767.

HAR- Harassment- If an auto-driver harass with you, you can complaint immediately to Delhi Traffic Police. For, harassment, the auto-driver can more hard punishment than any other complaints.

2. Use Helpline Number- If problem is worst for you while travelling in an auto-rickshaw, you can immediately call on 1095 or 25844444. It is 24x7 started helpline by Delhi Traffic Police and complaint will be listened and reacted as soon as possible.

3. Follow Social Networking Sites- You can also register complaint later on against the auto-driver. Only you have to note down his auto-rickshaw number. Page on Facebook is Delhi Traffic Police and follow on twitter - @delhipolice2. One can also use an email address- cp.neerajkumar@nic.in provided by Delhi Traffic Police.

4. Online Complaint Card- You can use online complaint card started by the Delhi Traffic police on their website. One has to fill all details related to complaint and can also mention brief description of 100 character against auto-rickshaw driver attitude.

Delhi Traffic Police has decided to take action against auto-rickshaw drivers within 24 hours of complaint registered. They are also working out on modalities to send an auto-generated text message to the complainant, acknowledging the receipt of the complaint along with a complaint registration number, so that he/she can follow up on the action taken.

Comments

How to Switch OFF Citizen Calculator

You might be confused on seeing no OFF button on your calculator. Actually, these are general calculator available at low cost in the market. They process simple calculations like division, subtraction, Addition, Multiplication. But, how will you OFF that calculator having no option on them. There is always a trick which OFF them. It depends on the company calculator and their series to which they belong. I can tell you about Citizen Calculator CT-500 (as you can see in the image), how can you switch OFF it and can save battery too. If you leave calculator idle for 6-7 minutes, it will goes OFF automatically. My calculator goes OFF in 6.50 minutes from the point of leaving it idle. But, this is not the power saving trick for these types of calculator having not much backup battery. To save the power of your normal calculator, here is the trick to switch OFF it. Press ' /(divide sign)', 'x(multiply sign)', '%(percentage sign)', 'autoreplay option(

Buzzer interface with 8051 microcontroller

Buzzer is a electronic device that converts the electronic signal into buzzing noise, that is applied to it. It can be used as electronic bell or as quiz buzzer in many applications around us. Here, i world like to discuss the interfacing of a small buzzer with 8051 microcontroller and how different projects can be constructed. Buzzer Interfacing: This project shows the interface with AT89S52 microcontroller to a buzzer. When a push button is pressed, the buzzer will get ON and OFF ( number of times set in the code ) and then stops. Circuit Diagram: - The port P1 of the microcontroller is connected to buzzer. This type of connection is possible, if the current requirements of the buzzer is not more than 20mA. The output is in current source mode so that buzzer will turn ON when the output of the port is logic LOW. Switch is connected to port P3 which remains at logic HIGH by pull up resistor. Code: #include "REG52.h" #define buz P1 sbit SW=P3^0; long int i; voi

Different ways to generate delays in 8051

The delay length in 8051 microcontroller depends on three factors: The crystal frequency the number of clock per machine the C compiler. The original 8051 used 1/12 of the crystal oscillator frequency as one machine cycle. In other words, each machine cycle is equal to 12 clocks period of the crystal frequency connected to X1-X2 pins of 8051. To speed up the 8051, many recent versions of the 8051 have reduced the number of clocks per machine cycle from 12 to four, or even one. The frequency for the timer is always 1/12th the frequency of the crystal attached to the 8051, regardless of the 8051 version. In other words, AT89C51, DS5000, and DS89C4x0 the duration of the time to execute an instruction varies, but they all use 1/12th of the crystal's oscillator frequency for the clock source. 8051 has two different ways to generate time delay using C programming, regardless of 8051 version. The first method is simply using Loop program function in which Delay() function i

Blogging & Tech tipps

Search This Blog