Get Email Alerts of Broken Links of your Website

When you read a post or visit a website and click on the provided links, you may not get visited to the particular links or found the broken links on that website. It mostly happens with images which are not displayed properly in your post. It occurs due to broken links from that site which an admin has linked in hos/her posts.

This is frustrating for both blogger and readers as it gives bad user experience. It's will be tough to check each and every post to avoid broken links. To avoid broken links on your WordPress website, you can download and install a plugin - Broken Link Checker.

Broken Link checker scans the broken links and provides the different option to dismiss, restore the links. It scans the whole site whenever you visit you wp-admin panel. You can also set the option to scan website in every few minutes or hours according to your adjustments.

The other cool features of Broken Link Checker is that it provides the scan details of broken links on your registered email. You have to set an email alerts whenever scan is done and broken links are found. You can also scan broken links in comment boxes, blogroll, pages, gallery etc.

How to adjust email alerts and scan time:

1. Firstly install broken link checker and Go to Settings -> Link Checker option.

2. You will find different options like scan in every few hours, status of broken links on your website, detected broken links, email notification etc. The second option - Check each link options and set scan time according to your convenience.

3. Now, you can see the Email notifications option. You can check the box to get the email alerts on your registered email after scan is done. In email, you will get all the broken links data, so that you analyze them easily.

4. In email, link is provided to correct the broken links your own. The broken link scan tool is under the category of Tools of your WP-admin panel.

You can also set which links have to be scanned by going to the Look for links in option in menu bar. Here, you can check the box where you want to find the broken links whether in your posts, comments, blogroll, gallery, and pages.

Comments

Comparison Chart Between 8051, 8052, 8031and 8751

8051 is a popular 8-bit microcontroller and has been used in many applications since Intel introduced it. Many 8051 architecture are produced by Triscend, Intel, Atmel, Philips, Infineon (Siemens), ISSI, and Max Corp. Today, 8051 microcontrollers may not be popular but, the 8051 architecture is still popular and employed in thousands of embedded applications. This 8-bit architecture has been different segments such as 8052, 8051, 8751 and 8031 . 8052 is the super-set of 8051 and 8031 is the memory-less microcontroller hence, it has interfaced with external ROM. Whereas, 8751 chip has only 4Kbytes of on chip UV-EPROM. Everyone knows about the general 40-pin microcontroller i.e. 8051 introduced by Intel in 1980s and consists of serial communication pins, Timer, Interrupts, RAM, ROM. It has 4 ports and each port has 8 pins, total 32 pins and other 8 pins for other purposes. 8052 is the super-set of 8051 that consists of 8K bytes of internal RAM (4K in 8051), 256 by...

Buzzer interface with 8051 microcontroller

Buzzer is a electronic device that converts the electronic signal into buzzing noise, that is applied to it. It can be used as electronic bell or as quiz buzzer in many applications around us. Here, i world like to discuss the interfacing of a small buzzer with 8051 microcontroller and how different projects can be constructed. Buzzer Interfacing: This project shows the interface with AT89S52 microcontroller to a buzzer. When a push button is pressed, the buzzer will get ON and OFF ( number of times set in the code ) and then stops. Circuit Diagram: - The port P1 of the microcontroller is connected to buzzer. This type of connection is possible, if the current requirements of the buzzer is not more than 20mA. The output is in current source mode so that buzzer will turn ON when the output of the port is logic LOW. Switch is connected to port P3 which remains at logic HIGH by pull up resistor. Code: #include "REG52.h" #define buz P1 sbit SW=P3^0; long i...

How to Switch OFF Citizen Calculator

You might be confused on seeing no OFF button on your calculator. Actually, these are general calculator available at low cost in the market. They process simple calculations like division, subtraction, Addition, Multiplication. But, how will you OFF that calculator having no option on them. There is always a trick which OFF them. It depends on the company calculator and their series to which they belong. I can tell you about Citizen Calculator CT-500 (as you can see in the image), how can you switch OFF it and can save battery too. If you leave calculator idle for 6-7 minutes, it will goes OFF automatically. My calculator goes OFF in 6.50 minutes from the point of leaving it idle. But, this is not the power saving trick for these types of calculator having not much backup battery. To save the power of your normal calculator, here is the trick to switch OFF it. Press ' /(divide sign)', 'x(multiply sign)', '%(percentage sign)', 'autoreplay option(...

Blogging & Tech tipps

Search This Blog