Skip to main content

Delete Wordpress Plugin show fatal error from cpanel

If you have WordPress site, you may know there are plenty of plugins and themes are available at free of costs. It is difficult to choose which one would be better to install. You can follow simple steps before installing plugins that generally occur different error messages or problems. Here are the steps to delete the plugin or theme that can not be deleted from your WordPress admin panel. So, delete it from your c-panel.  

Follow these steps:-

1. Log-in to your cpanel

2. Click on file manager option of your cpanel.

3. File manager will open up and right hand side containing different wp files. Now, find 'wp-content' file.

4. Now opening the wp-content file, find and click on the 'plugin' file option to open plugin directory of your site. Next, find the last plugin after installing showed error message.

5. Now, after finding the error plugin, select and delete that plugin immediately.
Labels:

Comments

  1. Ankita KumariMay 31, 2021 at 7:36 AM

    Thank you for sharing this informative post. Looking forward to read more.
    WordPress Development Services Delhi/NCR

    ReplyDelete
  2. AnonymousMay 31, 2021 at 2:06 PM

    Thanks for give us valuable information
    WordPress Support
    Contact WordPress

    ReplyDelete
  3. influence marketing platformOctober 10, 2021 at 4:17 AM

    Collection of WordPress themes with a graphical and textual preview available for each theme. Sorting and search feature as well. Influencer Marketing

    ReplyDelete

Post a Comment

Popular posts from this blog

Buzzer interface with 8051 microcontroller

Buzzer  is a electronic device that converts the electronic signal into buzzing noise, that is applied to it. It can be used as electronic bell or as quiz buzzer in many applications around us. Here, i world like to discuss the interfacing of a small buzzer with 8051 microcontroller and how different projects can be constructed. Buzzer Interfacing: This project shows the interface with AT89S52 microcontroller to a buzzer. When a push button is pressed, the buzzer will get ON and OFF ( number of times set in the code ) and then stops. Circuit Diagram: - The port P1 of the microcontroller is connected to buzzer. This type of connection is possible, if the current requirements of the buzzer is not more than 20mA. The output is in current source mode so that buzzer will turn ON when the output of the port is logic LOW. Switch is connected to port P3 which remains at logic HIGH by pull up resistor.  Code: #include "REG52.h" #define buz P1 sbit SW=P3^0; long int i; voi
13 comments
Read more

How to Switch OFF Citizen Calculator

You might be confused on seeing no OFF button on your calculator. Actually, these are general calculator available at low cost in the market. They process simple calculations like division, subtraction, Addition, Multiplication. But, how will you OFF that calculator having no option on them. There is always a trick which OFF them. It depends on the company calculator and their series to which they belong. I can tell you about Citizen Calculator CT-500 (as you can see in the image), how can you switch OFF it and can save battery too. If you leave calculator idle for 6-7 minutes, it will goes OFF automatically. My calculator goes OFF in 6.50 minutes from the point of leaving it idle. But, this is not the power saving trick for these types of calculator having not much backup battery. To save the power of your normal calculator, here is the trick to switch OFF it. Press ' /(divide sign)', 'x(multiply sign)', '%(percentage sign)', 'autoreplay option(
13 comments
Read more

Different ways to generate delays in 8051

The delay length in 8051 microcontroller depends on three factors: The crystal frequency the number of clock per machine the C compiler. The original 8051 used 1/12 of the crystal oscillator frequency as one machine cycle. In other words, each machine cycle is equal to 12 clocks period of the crystal frequency connected to X1-X2 pins of 8051. To speed up the 8051, many recent versions of the 8051 have reduced the number of clocks per machine cycle from 12 to four, or even one. The frequency for the timer is always 1/12th the frequency of the crystal attached to the 8051, regardless of the 8051 version. In other words, AT89C51, DS5000, and DS89C4x0 the duration of the time to execute an instruction varies, but they all use 1/12th of the crystal's oscillator frequency for the clock source. 8051 has two different ways to generate time delay using C programming, regardless of 8051 version. The first method is simply using Loop   program function in which Delay() function i
4 comments
Read more