Skip to main content

How to get rid of Spam mails in your E-mail account

If you frequently visit different sites and subscribe newsletter, you will experience your inbox full of spam mails. You will start suffering from email overload in your email accounts. And filtering all these unwanted emails may frustrate you. So, here is the solution of those who ready to filter there account using web application called 'sanebox'. Sanebox.com provides the pricing mail filtering and managing service for the users by integrating with one's email account.

Follow the steps to configure Sanebox:
1. Go to http://sanebox.com and fill up your email address which you want to filter from spam and then, click on 'sign-up'.

2. It will then contact your email service provider for authorization and may ask you for username and password and other details at your service provider's end. After this, it will analyze your email accounts and prepare the raw data of spam mails, read mails and sent mails.

3. After this, it will create two mailboxes, one called @SaneLater and other called @SaneArchive. All the new coming mails, it finds  you don't need to attend right now , will be placed in the mailbox @SaneLater and mails that are old and still in your inbox will be moved to @SaneArchive.

4. It will take to become friendly with Sanebox tools and you are required to train it what emails are being moved to the archive. You will get a Sane Digest daily in order to train it what mails you usually read and which mails you don't want to read or open.

Sanebox gives 14 day trail version and to upgrade it you are required to pay. And once you train your Sanebox, it will show up only useful mails to your inbox. For a few days, you will find it difficult to get used to as your emails will not show up in the old inbox. But, once you train the app, you can focus on things that need your attention. If you don't like it, you cancel the account anytime to put the mails back as were they.

Comments

Popular posts from this blog

Buzzer interface with 8051 microcontroller

Buzzer  is a electronic device that converts the electronic signal into buzzing noise, that is applied to it. It can be used as electronic bell or as quiz buzzer in many applications around us. Here, i world like to discuss the interfacing of a small buzzer with 8051 microcontroller and how different projects can be constructed. Buzzer Interfacing: This project shows the interface with AT89S52 microcontroller to a buzzer. When a push button is pressed, the buzzer will get ON and OFF ( number of times set in the code ) and then stops. Circuit Diagram: - The port P1 of the microcontroller is connected to buzzer. This type of connection is possible, if the current requirements of the buzzer is not more than 20mA. The output is in current source mode so that buzzer will turn ON when the output of the port is logic LOW. Switch is connected to port P3 which remains at logic HIGH by pull up resistor.  Code: #include "REG52.h" #define buz P1 sbit SW=P3^0; long i...

Comparison Chart Between 8051, 8052, 8031and 8751

8051 is a popular 8-bit microcontroller and has been used in many applications since Intel introduced it. Many 8051 architecture are produced by Triscend, Intel, Atmel, Philips, Infineon (Siemens), ISSI, and Max Corp. Today, 8051 microcontrollers may not be popular but, the 8051 architecture is still popular and employed in thousands of embedded applications. This 8-bit architecture has been different segments such as 8052, 8051, 8751 and 8031 . 8052 is the super-set of 8051 and 8031 is the memory-less microcontroller hence, it has interfaced with external ROM. Whereas, 8751 chip has only 4Kbytes of on chip UV-EPROM. Everyone knows about the general 40-pin microcontroller i.e. 8051 introduced by Intel in 1980s and consists of serial communication pins, Timer, Interrupts, RAM, ROM. It has 4 ports and each port has 8 pins, total 32 pins and other 8 pins for other purposes. 8052 is the super-set of 8051 that consists of 8K bytes of internal RAM (4K in 8051), 256 by...

Different ways to generate delays in 8051

The delay length in 8051 microcontroller depends on three factors: The crystal frequency the number of clock per machine the C compiler. The original 8051 used 1/12 of the crystal oscillator frequency as one machine cycle. In other words, each machine cycle is equal to 12 clocks period of the crystal frequency connected to X1-X2 pins of 8051. To speed up the 8051, many recent versions of the 8051 have reduced the number of clocks per machine cycle from 12 to four, or even one. The frequency for the timer is always 1/12th the frequency of the crystal attached to the 8051, regardless of the 8051 version. In other words, AT89C51, DS5000, and DS89C4x0 the duration of the time to execute an instruction varies, but they all use 1/12th of the crystal's oscillator frequency for the clock source. 8051 has two different ways to generate time delay using C programming, regardless of 8051 version. The first method is simply using Loop   program function in which Delay() funct...