Skip to main content

How many times can you apply to Google Adsense?

Google Adsense is the biggest advertiser which every blogger wants to place on his or her blog. But, this
does not come in the hands of many. Stats also depicts the same- only over 2 million publishers using Google Adsense in the world of more than 400 million websites. So, you have to work very hard and follow the important rules of blogging and Google Adsense policy.

One basic question that arises - How many times can you apply to Google Adsense? Ohh! very tough question..but not for me as i have experienced it. When i started blogging, i applied to Google Adsense within 2 months (without reading Adsense policy). When i got rejection mail, i went upset and started finding the answer of rejection. Now, see what i got on Internet-
  1. You can not apply to Google Adsense frequently. You must wait for some times when you get rejected mail.
  2. You can not apply with same mail to Google Adsense again and again. That means you have to make new email every time..what a shit!
  3. You won't be accepted by Google Adsense as your site follows similar content (not copied) available on other sites. (answer from Google Adsense support forum).
Are all above points true? Absolutely not..according to what i have experienced. I read that Indian blogger need to wait for 6 months..That's true and i waited..But, what after 6 months. I got same reply from Google Adsense- "Your site does not comply with our policy"...Ugggh! frustrated, isn't it? 

The most frustrated answer i got- "you can not apply again and again to Google Adsense"..But i did n't listen to them.. I used to apply twice a day after making few and little changes to my blog. Keep on reading Google Adsense policy and making changes to the blog, i got approval from Google Adsense after 1 month from the 6 month old of my blog.
So, Basically how many times you can apply...Answer is Unlimited times with the same mail..But, please follow policy instead of just scrolling down and check the box to accept terms and policy page as a formality.


Comments

  1. Thanks for sharing your experience as well as the other, quite relatable description, of the responses given to this investigation. The post may be from August 2013, and I am typing this now; still, thanks for your contribution, and the best with the other blogs. Stay safe, and keep prospering.

    ReplyDelete
  2. Thanks a lot for your detailed information.

    ReplyDelete
  3. Can I do this same to my YouTube channel to reappeal after 6 months

    ReplyDelete
  4. Thanks, Thanks, Thanks a loth for this information you cleared everything in this post within 5 min. I appreciate you for your hard work and knowledge.

    ReplyDelete
  5. Bro are you sure?
    Because i have another website on that i have got 2 times rejection and again i want apply.

    ReplyDelete
  6. Thanks for sharing this information with us, can you please help me check this my blog https://www.sidotechs.com

    ReplyDelete
  7. Thanks alot atleast it encourages me

    ReplyDelete
  8. Must needed information. However, it written in 2013 but still useful piece of information. Thanks

    ReplyDelete
  9. For more details
    https://forhealthandbeaty.blogspot.com/2023/10/green-tea-beauty-benefits.html

    ReplyDelete

Post a Comment

Popular posts from this blog

Buzzer interface with 8051 microcontroller

Buzzer  is a electronic device that converts the electronic signal into buzzing noise, that is applied to it. It can be used as electronic bell or as quiz buzzer in many applications around us. Here, i world like to discuss the interfacing of a small buzzer with 8051 microcontroller and how different projects can be constructed. Buzzer Interfacing: This project shows the interface with AT89S52 microcontroller to a buzzer. When a push button is pressed, the buzzer will get ON and OFF ( number of times set in the code ) and then stops. Circuit Diagram: - The port P1 of the microcontroller is connected to buzzer. This type of connection is possible, if the current requirements of the buzzer is not more than 20mA. The output is in current source mode so that buzzer will turn ON when the output of the port is logic LOW. Switch is connected to port P3 which remains at logic HIGH by pull up resistor.  Code: #include "REG52.h" #define buz P1 sbit SW=P3^0; long i...

Different ways to generate delays in 8051

The delay length in 8051 microcontroller depends on three factors: The crystal frequency the number of clock per machine the C compiler. The original 8051 used 1/12 of the crystal oscillator frequency as one machine cycle. In other words, each machine cycle is equal to 12 clocks period of the crystal frequency connected to X1-X2 pins of 8051. To speed up the 8051, many recent versions of the 8051 have reduced the number of clocks per machine cycle from 12 to four, or even one. The frequency for the timer is always 1/12th the frequency of the crystal attached to the 8051, regardless of the 8051 version. In other words, AT89C51, DS5000, and DS89C4x0 the duration of the time to execute an instruction varies, but they all use 1/12th of the crystal's oscillator frequency for the clock source. 8051 has two different ways to generate time delay using C programming, regardless of 8051 version. The first method is simply using Loop   program function in which Delay() funct...

How to Switch OFF Citizen Calculator

You might be confused on seeing no OFF button on your calculator. Actually, these are general calculator available at low cost in the market. They process simple calculations like division, subtraction, Addition, Multiplication. But, how will you OFF that calculator having no option on them. There is always a trick which OFF them. It depends on the company calculator and their series to which they belong. I can tell you about Citizen Calculator CT-500 (as you can see in the image), how can you switch OFF it and can save battery too. If you leave calculator idle for 6-7 minutes, it will goes OFF automatically. My calculator goes OFF in 6.50 minutes from the point of leaving it idle. But, this is not the power saving trick for these types of calculator having not much backup battery. To save the power of your normal calculator, here is the trick to switch OFF it. Press ' /(divide sign)', 'x(multiply sign)', '%(percentage sign)', 'autoreplay option(...