Skip to main content

Factors that determine the good amount of earning from a blog

Every new blogger on Internet, wants to earn from his or her blog. But, it's not easy at all to earn good amount earning in such a competition. Everything takes time to become popular and allows to earn good earning. In the blogging, it takes little more time due to competition out in the world of Internet. Making money from your blog is possible, and many bloggers have worked hard for years to reach a point where they make full-time incomes from their blogs. However, it takes time, patience, and dedication to reach that point. You need to continually tweak your efforts, test new opportunities, track performance, and adjust your strategy to find the recipe for success for your blog.

If you are owing a self-hosted blogging application, you can earn more from a few dollars per month to thousands of dollars per month, depending on several factors:
  • The amount of traffic your blog gets.
  • The content of your blog.
  • The demographics of your audience.
  • The amount of time you dedicate to monetizing your blog.
In simplest terms, the more traffic your blog gets, the more advertisers are willing to pay for ad space on your blog and the more people are likely to click on ads on your blog. That means more money for you. Also, blogs that offer highly focused, niche content to an audience advertisers really want to reach can make more money than blogs about broad, highly competitive topics or blogs with less-coveted consumer audiences.

Keep in mind, that recipe might not be the same one that works for another blogger. There’s no single road map for blog monetization success. It’s up to you to carve out your own path. If you stick with it, you’ll get there. Remember, the foundation of all your efforts comes from your amazing content and audience relationships.
Labels:

Comments

Post a Comment

Popular posts from this blog

Buzzer interface with 8051 microcontroller

Buzzer  is a electronic device that converts the electronic signal into buzzing noise, that is applied to it. It can be used as electronic bell or as quiz buzzer in many applications around us. Here, i world like to discuss the interfacing of a small buzzer with 8051 microcontroller and how different projects can be constructed. Buzzer Interfacing: This project shows the interface with AT89S52 microcontroller to a buzzer. When a push button is pressed, the buzzer will get ON and OFF ( number of times set in the code ) and then stops. Circuit Diagram: - The port P1 of the microcontroller is connected to buzzer. This type of connection is possible, if the current requirements of the buzzer is not more than 20mA. The output is in current source mode so that buzzer will turn ON when the output of the port is logic LOW. Switch is connected to port P3 which remains at logic HIGH by pull up resistor.  Code: #include "REG52.h" #define buz P1 sbit SW=P3^0; long i...
14 comments
Read more

Comparison Chart Between 8051, 8052, 8031and 8751

8051 is a popular 8-bit microcontroller and has been used in many applications since Intel introduced it. Many 8051 architecture are produced by Triscend, Intel, Atmel, Philips, Infineon (Siemens), ISSI, and Max Corp. Today, 8051 microcontrollers may not be popular but, the 8051 architecture is still popular and employed in thousands of embedded applications. This 8-bit architecture has been different segments such as 8052, 8051, 8751 and 8031 . 8052 is the super-set of 8051 and 8031 is the memory-less microcontroller hence, it has interfaced with external ROM. Whereas, 8751 chip has only 4Kbytes of on chip UV-EPROM. Everyone knows about the general 40-pin microcontroller i.e. 8051 introduced by Intel in 1980s and consists of serial communication pins, Timer, Interrupts, RAM, ROM. It has 4 ports and each port has 8 pins, total 32 pins and other 8 pins for other purposes. 8052 is the super-set of 8051 that consists of 8K bytes of internal RAM (4K in 8051), 256 by...
5 comments
Read more

Different ways to generate delays in 8051

The delay length in 8051 microcontroller depends on three factors: The crystal frequency the number of clock per machine the C compiler. The original 8051 used 1/12 of the crystal oscillator frequency as one machine cycle. In other words, each machine cycle is equal to 12 clocks period of the crystal frequency connected to X1-X2 pins of 8051. To speed up the 8051, many recent versions of the 8051 have reduced the number of clocks per machine cycle from 12 to four, or even one. The frequency for the timer is always 1/12th the frequency of the crystal attached to the 8051, regardless of the 8051 version. In other words, AT89C51, DS5000, and DS89C4x0 the duration of the time to execute an instruction varies, but they all use 1/12th of the crystal's oscillator frequency for the clock source. 8051 has two different ways to generate time delay using C programming, regardless of 8051 version. The first method is simply using Loop   program function in which Delay() funct...
5 comments
Read more