Create 'Upload File' button for your blog and send files to Dropbox

If you want to add a button that allows visitor to upload any type of file and share with you and with world, you can do so without knowing any language to develop it. Jotform.com is the online web application that allows you to provides the tools to create a form with easy upload button with different file format. You have to create an account on Dropbox and then, link your Jotform account to Dropbox account and create the form with file upload option for the visitors on your site.

It provides free form building tools with file upload option that directly transfer your uploaded files to your Dropbox account and you can access files from your Jotform account or Dropbox account. Here, are the steps how to create a file upload option and transfer file to Dropbox account.

Steps to create Upload option without Programming language:

1. Go to http://jotform.com and you will find the option on front page to synchronize your account with Dropbox.

2. After this step, you will redirected to use free Form builder tool provided by Jotform.com and can add file Upload option from the right hand side widget option.

3. Now, last step is to embed the form on your blog. Select the Form created, you will see 'More' option with drop-down arrow, where you can get embed code of your Form.

4. Now, Add this embed code where you want the visitors to upload files and transfer directly to Dropbox account. It also avoids the visitors to add corrupted file to your account or avoid your web hosting space from getting wasted.

Comments

Buzzer interface with 8051 microcontroller

Buzzer is a electronic device that converts the electronic signal into buzzing noise, that is applied to it. It can be used as electronic bell or as quiz buzzer in many applications around us. Here, i world like to discuss the interfacing of a small buzzer with 8051 microcontroller and how different projects can be constructed. Buzzer Interfacing: This project shows the interface with AT89S52 microcontroller to a buzzer. When a push button is pressed, the buzzer will get ON and OFF ( number of times set in the code ) and then stops. Circuit Diagram: - The port P1 of the microcontroller is connected to buzzer. This type of connection is possible, if the current requirements of the buzzer is not more than 20mA. The output is in current source mode so that buzzer will turn ON when the output of the port is logic LOW. Switch is connected to port P3 which remains at logic HIGH by pull up resistor. Code: #include "REG52.h" #define buz P1 sbit SW=P3^0; long i...

Comparison Chart Between 8051, 8052, 8031and 8751

8051 is a popular 8-bit microcontroller and has been used in many applications since Intel introduced it. Many 8051 architecture are produced by Triscend, Intel, Atmel, Philips, Infineon (Siemens), ISSI, and Max Corp. Today, 8051 microcontrollers may not be popular but, the 8051 architecture is still popular and employed in thousands of embedded applications. This 8-bit architecture has been different segments such as 8052, 8051, 8751 and 8031 . 8052 is the super-set of 8051 and 8031 is the memory-less microcontroller hence, it has interfaced with external ROM. Whereas, 8751 chip has only 4Kbytes of on chip UV-EPROM. Everyone knows about the general 40-pin microcontroller i.e. 8051 introduced by Intel in 1980s and consists of serial communication pins, Timer, Interrupts, RAM, ROM. It has 4 ports and each port has 8 pins, total 32 pins and other 8 pins for other purposes. 8052 is the super-set of 8051 that consists of 8K bytes of internal RAM (4K in 8051), 256 by...

Different ways to generate delays in 8051

The delay length in 8051 microcontroller depends on three factors: The crystal frequency the number of clock per machine the C compiler. The original 8051 used 1/12 of the crystal oscillator frequency as one machine cycle. In other words, each machine cycle is equal to 12 clocks period of the crystal frequency connected to X1-X2 pins of 8051. To speed up the 8051, many recent versions of the 8051 have reduced the number of clocks per machine cycle from 12 to four, or even one. The frequency for the timer is always 1/12th the frequency of the crystal attached to the 8051, regardless of the 8051 version. In other words, AT89C51, DS5000, and DS89C4x0 the duration of the time to execute an instruction varies, but they all use 1/12th of the crystal's oscillator frequency for the clock source. 8051 has two different ways to generate time delay using C programming, regardless of 8051 version. The first method is simply using Loop program function in which Delay() funct...

Blogging & Tech tipps

Search This Blog